Great Techniques For Cutting Men's Hair

Cutting hair is definitely an art form as well as there's really not a right or wrong to be able to achieve great results with a new hair-do. Each approach will vary by stylist, but there couple of basic principals right ? barbers and stylists can implement increase speed and quality when cutting men's hair. Good technical skill will also help increase your male client maintenance. Following are my thoughts on men's haircutting techniques:

Wet or Dried up?

Clipper work is close to always performed best in dry hair. It is indeed my opinion that blending should also be carried out in dry hair. Once the hair is wet, it can be difficult to see lines and hard to tell exactly how the head of hair is going to put when cut. Your hair should be wet for most shear and razor perform it's magic.

Cross Checking

When performing a haircut, cross-checking is essential. To some, this may be understood as an unnecessary step, but it extremely important to make sure the cut is even and proportional. When doing little haircut, check for blending and tapering in the mirror (or stand back a few feet). Often, you view things from a distance that completely miss up strong. Also make sure to have proper lighting from all angles. Dim light and shadows permit very hard to check for quality in the cut.

Anchor-Pivot-Suspend

The first part in good blending is avoiding lines of demarcation in the initial place. When performing clipper work, go through three steps with each action. Start with the clipper anchored with the entire flat surface of the blade touching the head. Moving upward, pivot the clipper so only the heel (back) in the blade is touching. Next, suspend the clipper freehand while moves up and out of the head of hair. This will create the smoothest transition possible.

Blending: Clipper-Over-Comb

One method of blending between clipper and shear hardwork is to use the clipper-over-comb method. In this technique, use a detachable blade clipper with a large blade (#1 1/2 or higher). Clothes airers blade will provide client a smoother blend because your hair will be cut a uniform length with a feathered end. Never make use of a short blade or trimmer to blend because the blades will give the head of hair a very blunt cut and leave lots of small lines of bevel clippers demarcation.

Blending: Blending Shears

Another ways of blending is blending-shears-over-comb. Lift the hair up your comb and use the blending shears to cut the last 1/4" within the hair. When lifting the hair, it's vital to slightly overdirect before cutting given that will creates a smoother unique blend. Remember to only cut the last 1/4'" to 1/8" of hair. Never thin hair close to the scalp simply because will create a fuzzy look by causing very short hairs to stay out your longer hair. Use a thinning shear with at least 40 smile. Shears with larger teeth will produce design. Avoid using regular shears to combine because the blades provides the hair a very blunt cut and leave lots of small lines of demarcation.

Blending: Haircutting Razor

You additionally be create a blend using the straight razor (without a comb attachment). The hair is raked with the razor at a 45 degree angle. The angle of this blade is essential. If the blade is kept in a more flattened position, very much hair will be removed. If the blade is held more upright, it's damage the cuticle. Method was latched onto by the Roffler schools and will not be attempted til you have received hands-on training by a barber/stylist which skilled in the technique. For razor blending, it is essential that your hair be very wet.

Texturizing

A razor (with guard) or shear-point techniques should be employed to required haircut texture by cutting the ends of your hair in obvious, varying hair strands. Texture is desirable in haircuts that are worn spiked or disheveled. The razor (with guard) is employed to strip the ends for this hair between the blade along with the thumb to create the varying lengths. When pulling the head of hair between the razor and thumb, hold the razor with an angle and use a scooping motion. The shear-point technique is used to cut the ends of the head of hair at an angle (or even snipping out alternating pieces) to add texture. Perform these techniques only after hands-on instruction from a knowledgeable instructor.

Finishing

Many stylists will spend a good deal of time positive a haircut is well blended and even, but skimp near the finishing. A splendid haircut can be completely destroyed by poor finishing (a bad haircut can additionally be made respectable with good finishing). It is critical to make sure all lines (the arch around the ear and also the neckline) are clean and neat. Most haircuts will benefit from slight tapering or beveling around the underside edges. When you are conducting sideburns, stay at home front for this client look at him directly in confront to ensure evenness. Check to is vital to keep bangs are straight also.

Necklines: Blocked or Tapered?

Many stylists and barbers will consider the shortcut of blocking the client's hairline. Often, this can be a disservice to your client. A tapered haircut will give you wide neck a slimmer appearance and will look neater as the cut grows out. On the blocked haircut, the neck hair will grow out below the block as well as the client may have a line in your hair on the rear of his head. A tapered haircut blends with no hair the way it grows outdoors. Blocking can give a slim neck more balance, which could teach you often a great choice. When blocking, your hair should be blocked because on the neck while you possibly so there will be less hair below the cloths line as the cut grows out.

Clipper Guards

Many in the industry are firmly against the utilization of clipper protects. The main argument against guards is that anyone can snap on the guard gives you a haircut, so the feeling is various clients will ever try to cut their own hair. A lot is, however, that most clients will not be able to obtain professional looking results inside. Only those trained in cutting hair will be able to accomplish the proper finishing, blending, and tapering needed to make a clipper cut look reliable.

As for technique, quite a few things to keep in their mind if you choosed to use protects. When using a clipper with guards, stick to the anchor-pivot-suspend technique and cut against the rise pattern. Avoid cutting in an angle since this will create small lines because of the way the guard separates the hair before it feeds into the blades. Next, make guaranteed to go over each part of hair a couple of times to ensure all tresses are cut. Avoid forcing your hair into the cutting blades with a comb perhaps hands due to the fact will create lines of demarcation. Always comb the hair before each stroke, but make sure the comb is among the way in advance of the clipper runs through the following. Finally, avoid guards that leave the hair longer than 1/2 within .. Clippers will only effectively cut hair you might find enough tension on the hair to force it in the cutting razors. Larger guards do not allow enough tension and, thus, will leave much on the hair un-cut.

Posted on Tags